code height for a platform railings

WAC 296-24-75011: Railing, toeboards, and cover specifications. (e) Other types, sizes, and arrangements of railing construction are acceptable provided they meet the following conditions: (i) A smooth-surfaced top rail at a height above floor, platform, runway, or ramp level of from 36 to 42 inches nominal;. (ii) A strength to withstand at least the minimum requirement of 200 pounds top rail

Building Code Guidelines: Decking Railing Heights, Guards, and Feb 17, 2017 If you decide to construct a guard on a deck low enough that it doesn't require guards, it is up to you as to guard rail height and baluster spacing. However, these guards still must be as strong as guards located higher on decks. It is understood that people will lean against guards, and code requires that

Railings - United States Access Board (See 2000 International Building Code, below.) This will allow a design professional to increase the guardrail height if a specific location needs enhanced safety measures or a local building code applies. Dispersion Anglers who can stand are able to fish from any part of a pier or platform and change locations. To provide

Guardrail height requirements for construction activities in General Apr 17, 2006 (1) A standard railing shall consist of top rail, intermediate rail, and posts, and shall have a vertical height of 42 inches nominal from upper surface of top rail to floor, platform, runway, or ramp level. * * * [Emphasis added.] However, OSHA Directive STD-01-01-010 — Height of Guardrails in General Industry

PDS #075 - County of San Diego Guards are required at the following locations per Section 1015 the 2016 California Building Code: ? Along open-sided walking surfaces, mezzanines, industrial equipment platforms, stairways, ramps and landings that Guards shall form a protective barrier not less than 42 inches high except for stair railings in Group R-3.

Building Codes - Information and Guidelines BuyRailings The height will vary depending on the code. The IBC requires a guard to be 42" in height. Handrails are located between 34" and 38" and have dimensional limitations for graspability. As such, if a 42" guardrail is called for on a stair or ramp, it will also require a secondary handrail at the appropriate height. A guard top rail

Know the Requirements for General Industry -- Occupational Health Sep 1, 2012 Under 1910.23(e)(1), OSHA says that a guardrail must have a vertical height of 42 inches nominal from the upper surface of the top rail to floor, platform, runway, or ramp level. "Nominal" simply means that 42 inches has been established as the de facto standard for guardrail height. OSHA allows for

10/28/2004 - Top rail and handrail requirements for stairrail systems Oct 28, 2004 Question: Under the construction standards, can a 42-inch-high top rail for a stairway also serve as a handrail, or must a handrail also be provided? We also note that a number of National and State building codes have stair rail (guardrail) and handrail provisions that mirror the OSHA standards set out

Guardrails: Guide to Guard Railing Codes, Specifications, Heights Guardrail code guide: stair landing guardrail codes, porch guardrail codes, deck & walkway guardrail specifications & codes: height, dimensions, spacing, construction Definition of a Guardrail Specifications & Defects: requirements for guard railings at stair platforms, landing guard railings & other elevated walkways

What is the Appropriate Height for Fall Protection Railing? - Fall What is the Appropriate Height for Fall Protection Railing? image. There are many different types of railings on the market, not to mention the 2x4 or wire rope job-built railings you find on many construction sites. Regardless of their style or mounting method, they all must meet the same criteria. All must be capable of

OSHA Requirements for Guardrail and Safety Railing Compliance Feb 1, 2017 In the interest of time, here is OSHA's official stance on guardrail for general industry applications…. OSHA 1910.29(b) contains system requirements that employers must follow to ensure guardrail systems will protect workers from falling to lower levels: 1910.29(b)(1) The top edge height of top rails,

Guardrails: Design Criteria, Building Codes, & Installation - Buildipedia Feb 16, 2010 Guardrail systems are installed to provide safety and protection for the building occupants and are placed at or near the outer edges, of flights of stairs, ramps, landings, platforms, balconies and accessible areas of roofs. They will also be found at the perimeter edge of any opening or accessible surface,

What is the maximum height for a terrace without a guard rail? Apr 6, 2016 The 2012 International Building Code (IBC 2012) generally requires guardrails when the difference in elevation between the upper and lower surfaces is 30 inches or greater. 1013.2 Where required. Guards shall be located along open-sided walking surfaces, including mezzanines, equipment platforms,

Subchapter G. RAILINGS, TOEBOARDS, OPEN-SIDED - PA Code Railing—A vertical barrier erected along the exposed edges of open-sided floors, working platforms, runways, balconies and openings in walls, floors and ground (a) Railings shall be not less than 42 inches in height from floor or ground level to the top of the top railing and shall be provided with an intermediate railing the

commercial stairs, railings, & guards - City of Marion 6'-8” Minimum. Headroom. Handrails to extend one tread depth past the bottom riser. 34” – 38” to top of handrail. Handrails shall return to a wall, guard, or the walking surface or be Maximum vertical rise of a stair run must not exceed 12 feet without a landing or intermediate platform. However, if a landing occurs in a

Guardrails/Fall Protection At Elevated Locations (Non-Construction) In existing installations where clearance prohibits railings on the outside of the platform, railings will be permitted on the building side to serve as handholds. would obstruct the sight lines, may be protected by a guardrail or other barrier of not less than 34 inches in height provided that a horizontal concave safety ledge not

Five Key OSHA Standards for Work Platforms - Spika Blog May 30, 2017 The top edge height may exceed 45 inches (114 cm), provided the guardrail system meets all other criteria. Spika Work Platform Mars Series. This may be the quintessential OSHA requirement for work platforms. Any work area four feet or more above the next level lower MUST have guardrails. Period.

Compliance of stair and platform railings with height requirements in Standard Interpretations; Compliance of stair and platform railings with height requirements in OSHA standards for fixed industrial stairs. Proposed §1910.28(b)(3)(ii) would allow guardrails installed prior to 60 days from the publication date of the final standard to have a guardrail height of a minimum of 36 inches.

Guardrails - Florida Building Code 5th Edition (2014) - Barfield Aug 17, 2016 Florida Building Code SECTION 1013 GUARDS. (Located in Florida Building Code Chapter 10 – Means of Egress). 1013.1 General. Guards shall comply with the provisions of Sections 1013.2 through 1013.7. Operable windows with sills located more than 72 inches (1.83 m) above finished. grade or other

Product Details

Product List